The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi guys we had an issue routing to webex calling to our on prem cucm via the trunk.we could not dial webex users from our cucm via the trunk, but we could dial the same numbers from webex to cucm.i added a route to the source number from webex to poi...
Dear allPlease help to check this errorMany thanks & Best reagard!Bootable image at @ ram:0x53778350Bootable image segment 0 address range [0x81100000, 0x82140000] is in range [0x80180000, 0x90000000].@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@...
Hello all,I hope all is well.I am new to coding in general. I am currently learning python from what I have been told by a friend who is advance in python that the best way to learn the language is to practice with projects so I thought I would use o...
If i create an event manager applet to capture logs, i can work with a variable called $_syslog_msg. Example:event manager applet RUNATEVERYLOG event syslog pattern "Configured programmatically" maxrun 4 action 1.0 cli command "enable" action 2.0 put...
Hi all,I have locked myself out of the switch, more specifically, I can't enable. Every method of password recovery I have tried has failed. I do not know how to factory reset my two stackwise-enabled switches. I need a password recovery procedure th...
Hello Community,Is there any command to turn-off the paging of the commands output on Cisco iOS and display all output without paging? On Dell Switches, there's a command "terminal length 0", but the same doesn't seem available on Cisco iOS.Router#te...
Hello Folks, I have a pair of ASA5516 with HA mode, ISP provides a high-speed WAN 500Mbps up/download, while doing some speed tests recently we noticed that all our tests from the inside network are not bypassing 100mbps, I checked all inside/outside...
Hello,I am labbing with an 9300v (10.3(1)) and some XRv boxes, trying to have the not ldp 9300v talk to the rest of the ldp boxes.I was thinking of having one of the XRv boxes act as a mapping server, so that the 9300v could receive the prefix-sids m...
Hi, I have three CBS220-48P-4G-SW1 configured with LAG uplink consisting of two port between each of those switches.When I try to enable LACP on those LAG I get an error code 387.Does anybody got this issue and figured how to resolve it ?
I need to clarify if my Switch sg220-26 has POE ports. The documentation is confusing and I CANNOT see the POE Option for Port Management by entering as Switch Administrator.Otherwise, it is possible to make this Switch POE by placing some external s...
I have an intermittent internet cut off after around some days of working (5 to 10 days). The router becomes inaccessible by ssh. No ping also from internet and from inside. The architecture includes two switches (CBS350-48FP-4X) with Vlan1.We did no...
Necesito aclarar si mi Switch sg220-26 tiene puertos POE. La documentación es confusa y NO logro ver la Opción POE para la administración de Puertos ingresando como administrador del Switch.De lo contrario es posible lograr que este Switch sea POE co...
Hello,I am new to networking and have been unable to pin point the source of the issue. We have two CBS 250 devices that have been acting odd lately. 2-4 times a week the management interface would disconnect for about 5-20 mins. I've compared config...
Tengo una pregunta que no entiendo sobre las redes Docker, Macvlan e ipvlan. En el primer ejemplo, quiero mostrarles la red en modo bridge Macvlan. Esto me funciona correctamente, les muestro lo que he hecho para que funcione correctamente. 1. Primer...